> For the complete documentation index, see [llms.txt](https://docs.onocoy.com/documentation/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.onocoy.com/documentation/3.-become-a-miner/explorer/live-view.md).

# Live View

### What the Live view shows <a href="#what-the-live-view-shows" id="what-the-live-view-shows"></a>

The Live view is a real-time health check of your reference station: if most numbers sit in the "healthy" ranges below, your station is doing its job. It refreshes continuously while the window is open, and the green **Live** badge in the top-right corner shows how long you have been watching (for example, Live · 4:05).

Use the Live view when you first install a station, after moving or adjusting the antenna, or when your Quality score drops and you want to find out why.

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2FHJzVyLORpYY9U3ioq4bX%2Fimage.png?alt=media&amp;token=c4de43da-3efc-4ef8-b077-1d670790f38a" alt=""><figcaption></figcaption></figure>

### Summary tiles <a href="#summary-tiles" id="summary-tiles"></a>

The eight tiles at the top give you the station's vital signs at a glance. The "healthy" column gives typical values for a well-installed station; they are rules of thumb, not official reward thresholds.

<table data-header-hidden><thead><tr><th width="168"></th><th></th></tr></thead><tbody><tr><td>Tile</td><td>What it means in plain words</td></tr><tr><td>Satellites</td><td>How many satellites your station is tracking right now. More satellites means more reliable data.</td></tr><tr><td>Signals</td><td>Total number of signals received. Modern satellites broadcast on several frequencies at once, so one satellite can provide 2 to 4 signals.</td></tr><tr><td>Latency (s)</td><td>Delay, in seconds, between the station taking a measurement and the network receiving it. Lower is better.</td></tr><tr><td>Mean C/N0 (dBHz)</td><td>Average signal strength across all satellites (C/N0 means "carrier-to-noise", i.e. how loud the signal is compared to background noise).</td></tr><tr><td>Code RMS (m)</td><td>How much the code (pseudorange) measurements scatter. These are the coarser, metre-level distance measurements to each satellite. Multipath (signals bouncing off walls, roofs or the ground before reaching the antenna) is the main cause of high values; weak signals and interference also raise it. Lower is better.</td></tr><tr><td>Phase RMS (m)</td><td>How much the carrier-phase measurements scatter. These are the millimetre-level distance measurements that make centimetre positioning possible, so this tile matters most for data quality. It rises with multipath, low signal strength and brief signal interruptions. Lower is better.</td></tr><tr><td>Clock drift (ppm)</td><td>How fast the receiver's internal clock is running too fast or too slow, in parts per million. Values close to zero are normal.</td></tr><tr><td>Clock bias (µs)</td><td>How far the receiver clock is offset from satellite time, in microseconds. A dash (–) means the value is not reported by your receiver, which is not a problem.</td></tr></tbody></table>

You rarely need to act on the clock tiles. Focus on Satellites, Mean C/N0 and Latency first: they reveal most installation problems.

### Signal level panel <a href="#signal-level-panel" id="signal-level-panel"></a>

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2FVCBqQAXfakjHFX5Awxyv%2Fimage.png?alt=media&amp;token=1446ea2d-7765-4b53-a3e0-6385a60f3d70" alt=""><figcaption></figcaption></figure>

This panel shows how strong your signals are on each frequency band, averaged over all satellites. Longer bars are better; bars of similar length across bands mean a healthy, balanced setup.

The scale runs from 25 to 55 dBHz. As a rough guide, values above 40 dBHz are good, 35 to 40 dBHz are acceptable, and values that stay below 35 dBHz suggest a problem such as a poor antenna location, a damaged cable or nearby interference.

It is normal for L1 to be slightly stronger than the other bands. Be concerned only if one band is much weaker than the rest, or missing entirely when your receiver should support it.

### Constellation table <a href="#constellation-table" id="constellation-table"></a>

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2FtZEXCp5SAjg7RrSgd3iD%2Fimage.png?alt=media&amp;token=1458e58c-42d0-4fc7-8c48-a14f1ef72405" alt=""><figcaption></figcaption></figure>

The table below the bars breaks your satellites down by satellite system and band, so you can see that your station receives all four major systems. A station that tracks all four is more reliable and more valuable to the network.

How to read a row: the **Satellites** column is how many satellites of that system are tracked; the band columns (L1, L2, L5, E5ab, L6) show how many signals are received on each band. A dash (–) means that system does not broadcast on that band, or your receiver does not track it. For example, GLONASS does not use L5, so a dash there is expected.

A signal count can be higher than the satellite count. In the example, BeiDou has 6 satellites but 11 L1 signals, because some BeiDou satellites send two signals within the same band.

### Sky view <a href="#sky-view" id="sky-view"></a>

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2F25JmFWcqfgiF0lLpKcdL%2Fimage.png?alt=media&amp;token=07880916-b0b4-476d-9376-dfc9606bfc3e" alt=""><figcaption></figcaption></figure>

The Sky view shows where the satellites your station is tracking right now are, relative to your antenna, and how strong each signal is. It is a live snapshot: only satellites currently in view appear.

For a longer-term picture, use the **Sky map** page. It builds up sky visibility across the whole sky over a 24 hour period. Use the Sky view to check what is happening now, and the Sky map to confirm a pattern.

Imagine lying on your back next to the antenna and looking straight up:

* **The centre** of the circle is directly overhead.
* **The outer edge** is the horizon.
* **The rings** mark the height above the horizon (elevation): the 30° ring is low in the sky, the 60° ring is high.
* **The letters and numbers around the edge** are compass directions: N (north) at the top, E (east) on the right, S (south) at the bottom, W (west) on the left. The numbers (30, 60, 120…) are bearings in degrees.

Each circle is one satellite. Its label combines the constellation letter (G GPS, R GLONASS, E Galileo, C BeiDou) and the satellite number, so **G20** is GPS satellite 20 and **E05** is Galileo satellite 5. The colour shows the signal strength, using the C/N0 scale on the right:

* **Yellow-green**: strong signal (around 40 to 45 dBHz). This is what you want.
* **Orange**: weaker signal, often from satellites low on the horizon.
* **Purple to grey**: very weak.
* **Dark grey or black**: the satellite is in the sky but your station is receiving little or no usable signal from it.

**What to look for.** Satellites near the edge are naturally weaker because their signal travels through more atmosphere, so some orange and dark markers low on the horizon are normal. Be concerned when a whole section of the sky is dark, even at higher elevations. That usually means something is blocking the view in that direction: walk to the antenna, face that compass direction and look for a wall, roof, tree or other obstruction. In the example, many dark markers cluster in the west and north-west, which suggests checking that side of the installation.

### Antenna position and velocity <a href="#antenna-position-and-velocity" id="antenna-position-and-velocity"></a>

These two panels confirm that your antenna is standing still. A reference station must never move, because the whole network relies on its position being fixed and known.

Both panels show a top-down circle (north, east, south, west) and a vertical scale for up and down (U).

The antenna position plot is a gross indicator of movement whilst the antenna position plot is a fine movement indicator

#### Antenna position <a href="#antenna-position" id="antenna-position"></a>

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2FYdjNUf4X39ZJSGhZCWip%2Fimage.png?alt=media&amp;token=6437806a-3860-4eeb-80c9-17dc668b1f69" alt=""><figcaption></figcaption></figure>

The dot shows how far the position your station calculates in real time is from its registered position, in metres, and the faint trail behind it shows recent movement.

This position uses satellites alone, without corrections, so wandering by a metre or two is normal. Watch for a jump that does not come back, or a steady drift in one direction: that can mean the mount has shifted.

#### Antenna velocity <a href="#antenna-velocity" id="antenna-velocity"></a>

<figure><img src="https://3173123995-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FjBN41DfVchs8L33Unu18%2Fuploads%2FkzqChF1wxURPeInREehw%2Fimage.png?alt=media&amp;token=99456159-f1e4-4bfa-997a-f845beac1016" alt=""><figcaption></figcaption></figure>

The dot shows how fast the calculated position is changing, in mm/s, and should sit at or near the centre. Regular large values point to a loose or swaying mount, or vibration.
